Protection Prescription

GLASS IQ

1. 1. MIST

   Lightly mist Glass IQ onto the glass surface. For larger surface areas, additional sprays may be needed to achieve full coverage.

2. 2. LET SIT

   Let sit for a moment, then remove excess with a clean microfiber towel.

3. 3. REPEAT

   Reapply as needed to restore protective properties.

For use only on light contamination: For heavier contamination, try Glass Cleanser.
Do not apply in direct sunlight.
Do not allow product to dry on surface.
In areas where overspray may occur, spray Glass IQ on the towel first and then wipe it onto the surface. Wipe it off with a separate towel.
Always test in an inconspicuous area first to check for surface compatibility.

LEATHER LOCK

1. 1. CLEAN

   Clean leather surface completely to ensure optimal protection.

2. 2. SATURATE

   Saturate a soft, clean microfiber towel with the product. Do not spray directly onto surface.

3. 3. WIPE

   Wipe the surface with the saturated towel, overlapping to maintain even coverage.

4. 4. LET CURE

   Once applied, do not disturb the surface for at least 3 hours or until completely dry. Leather Lock will take 24-48 hours before it fully cures and takes effect.

For best results: Clean leather with Fine Leather Cleanser and condition with Leather Cream before application.
Before applying: Test a small amount in an inconspicuous place to check compatibility with surface.
To maximize the longevity of your coating, regularly maintain leather with Leather Cream and Fine Leather Cleanser.

CARPET & UPHOLSTERY PROTECTION

1. 1. SHAKE

   Shake well.

2. 2. BRUSH

   Brush carpet fibers in one direction. Hold Carpet & Upholstery Protection bottle 8-12 inches from the surface and spray until the carpet is damp.

3. 3. BRUSH BACK

   Brush carpet fibers in the other direction and repeat.

4. 4. LET DRY

   Allow product to dry undisturbed for 24-48 hours.

Do not allow this product to freeze.
Before applying: Test a small amount in an inconspicuous place to check compatibility with surface.

FORMULA 1201

1. 1. WASH

   Wash vehicle.

2. 2. MIST

   Mist water on a panel.

3. 3. SHAKE

   Lightly shake the Formula 1201 bottle.

4. 4. PLACE DROPS

   Place 10 to 15 drops onto the applicator. (For subsequent panels, apply 5-6 drops.)

5. 5. APPLY

   Apply to wet panel in circular or straight back-and-forth motions.

6. 6. WIPE OFF

   Immediately wipe the panel down with a fresh microfiber towel.

7. 7. WIPE AGAIN

   Flip the towel over to a dry section and hand buff until the surface is glossy.

8. 8. REPEAT

   Repeat steps 2-7 until the entire vehicle is covered, applying 5-6 more drops with each panel.

Use distilled water for optimal durability.
To speed up application: Apply coating after the final wash rinse, skipping the drying step.
Do not wash vehicle for 7 days after applying.
Product may require 2 weeks of cure time before reaching optimal effectiveness.
Do not apply in direct sunlight.
Do not let freeze.
Before applying: Test a small amount in an inconspicuous place to check for surface compatibility.

WHEEL SEAL

1. 1. CLEAN & DRY

   Before use, be sure the wheel is clean and dry.

2. 2. SPRAY

   Apply Wheel Seal using a soft cloth.

3. 3. LET CURE

   Let it cure by leaving it on the surface for several minutes.

4. 4. HAND BUFF

   Use a soft cloth to hand buff for optimal protection.

For maximum results: Begin by cleaning the wheels with our Premium Wheel Cleanser before applying Wheel Seal.
Before applying: Test a small amount in an inconspicuous place to check compatibility with the surface.